| Most viewed - Basil Build |

161029-133125.jpgAdding peel ply151 views
|
|

161029-151232.jpgSealing the other end of the bag151 views
|
|

161129-180942.jpg150 views
|
|

170414-161221.jpg149 views
|
|

170417-145331.jpg149 views
|
|

170414-142511.jpg148 views
|
|

161029-131125.jpgSecond layer of carbon147 views
|
|

161115-175155.jpg146 views
|
|

161029-150052.jpgReady to be sealed144 views
|
|

170414-142446.jpg144 views
|
|

170417-160221.jpg144 views
|
|

170414-150702.jpg143 views
|
|

161029-141259.jpgFitting infusion mesh142 views
|
|

170414-142501.jpg141 views
|
|

161029-110614.jpgInserting core material139 views
|
|

161029-133114.jpgAdding peel ply139 views
|
|

161029-150259.jpgSealing the first end of the bag139 views
|
|

161028-133008.jpgAttaching the front bulkhead flange138 views
|
|

161029-143954.jpgCompleting feed system138 views
|
|

161029-153005a.jpgChecking for bridges138 views
|
|

161028-133115.jpgAttaching the front bulkhead flange137 views
|
|

161029-122850.jpgFinal view of core material137 views
|
|

161029-143855.jpgAdding spiral feed tubes137 views
|
|

161029-131127.jpgTrimming the carbon136 views
|
|

161029-145457.jpgStarting to bag bottom half mould136 views
|
|

161029-115446.jpgLining up the last piece of core material135 views
|
|

161029-151418.jpgPreparing the catch pot 135 views
|
|

161027-122543.jpgMr Dusty134 views
|
|

161029-133408.jpgFitting peel ply134 views
|
|

161029-152540.jpgAdjusting the pump pressure134 views
|
|

161029-112618.jpgCutting core material133 views
|
|

161029-145639.jpgMould in bag133 views
|
|

161029-152207.jpgMost of the air gone...133 views
|
|

161028-151907.jpgFirst layer of carbon132 views
|
|

161029-134328.jpgTrimming peel ply132 views
|
|

161028-144514.jpgCutting the wing130 views
|
|

161029-132655.jpgFitting the carbon130 views
|
|

161029-145021.jpgMould for top half of car130 views
|
|

161029-140751.jpgPeel ply layer complete128 views
|
|

161029-113859.jpgInserting core material127 views
|
|

161029-115953.jpgPutting in shuttering for the rear hatch127 views
|
|

161029-112840.jpgInserting core material125 views
|
|

161029-113513.jpgInserting core material124 views
|
|

161029-114345.jpgTrimming core material122 views
|
|

161029-145626.jpgLifting the bag onto the mould122 views
|
|

161029-141053.jpgCutting infusion mesh119 views
|
|

161029-154143.jpgSealing the front hatch frame119 views
|
|

161029-151552.jpgMaking a seal for the vacuum tube118 views
|
|

161029-141330.jpgFitting infusion mesh117 views
|
|

161028-151917.jpgFirst layer of carbon116 views
|
|
|
|
|
|
|
|